Audio Installation

Digiline 8


Digital mixers and DSP

Digiline 8is the most complete unit: in addition to processing features, it includes a powerful amplifier with 8 independent channels of 150 W each.
To maximize S/N ratio in audio signal, it features a double switching mode power supply: one for amplification and another for DSP. It has a small size (2U rack enclosure) and ensures maximum efficiency, thanks to the class D advanced amplifier system.

Inputs: 8 double MIC inputs (with phantom) + LINE balanced and one additional MIC input. All of them have Euroblock connector.
Outputs: 8 outputs with Euroblock connector.
Control interface: TCP/IP and GPI.
Control connections: RJ45 (Ethernet TCP/IP) and Euroblock (GPI).
Control software: WorkCAD Designer (included).
Control indicators: Frontal LED for signal presence.
Frontal controls: Gain control.
GPI inputs: 4 GPI (normally opened TTL inputs) for direct control.
Input sensitivity: 0 dBu
Phantom supply: 24 V MIC inputs.
THD+N: < 0.1 %.
Power requirement: 1300 W.
Main supply: AC 120 or 230 V (internally selectable).
Dimensions (WxHxD): 483 x 88 x 449 mm.
Digital matrix mixer of 8 x 8 (each input is composed of 2 inputs: 1 Mic and 1 Line).
Independent processing of signal for each output.
Controllable through TCP/IP protocol, in order to control from a unique computer all the units connected to an Ethernet network.
Third party controllers can be connected to control Digiline by TCP/IP and RS232 (RS232 only available in Digiline MX) thanks to the command reader incorporated by its firmware.
All MIC inputs are phantom powered.
Powerful software WorkCAD Designer for Digiline connexion through TCP/IP.
GPIO triggering mode to launch actions, presets, etc from a simple controller.
Only for Digiline 8: Built-in power amplifier (8 x 150 W RMS).
DSP features
Matrix mixer: 8 mixers of 8 channels with reverse signal and mute for any channel.
Crossover: Butterworth type filters, Linkwitz-Riley and Bessel up to 4° order with up to 7 fi lters per output.
Equalizer: Equalizations with peak type curves, low pass, high pass, notch, low shelving, high shelving and band pass with up to 7 filter per output maximum.
Dynamic control: Common Limiter compressor for first 7 channels and an independent one for the last one.
Output channel volume control: Selectable by software and frontal potentiometer (36 dB to -109 dB range). 48 bit processing architecture with 76 bits of precision for most audio processing features.
Presets memory: 10 program memories available.
DSP Architecture: 32 bit processing with 40 bits of precision.
Oversampling: 8 x Oversampling with fifth order noise shaping @ 32-48 kHz; 4 x Oversampling @ 88.2 and 96 kHz; 2 x Oversampling @ 176.2 kHz and 192 kHz.
Digital De-emphasis: For 32,44.1 and 48 kHz.

  Application Tip

So far, there are no questions related to this product.

Register to be able to ask a question about this product.

I accept terms and conditions regarding the treatment of my data.Make the question


Related Products

  • D 4T
    Low impedance/ 70-100V Line conversor. 4 channels. 150W each
  • MKS 1400
    Speaker cable. Black. 100m roll
  • WNC 1
    Ethernet wall-mounted for BlueLine or Digiline. 5 V DC.

Alternative Products

  • M 4300
    4 x 400 W @ 4 Ohm power amplifier. Switching power supply. Stereo/bridge/parallel modes
  • PA 1254
    Amplifier 4 x 150 W @ 4 Ohm. 9 operating modes. Crossover for subwoofer output.
This website uses cookies

Cookies on this website are used to personalize content and advertisements, provide social media features, and analyze traffic. In addition, we share information about your use of the website with our social media, advertising and web analytics partners, who may combine it with other information that you have provided to them or that they have collected from your use of their services. < / p> Only use necessary cookies Select cookies Allow all cookies More info